ARX Tyre Industry Equipment (Used) Exchange Listings

Quantity	Units	Frequency
1	eacch	once
Price	Funds	Per Unit
29,500	US Dollar	each

Tire Industry Equipment - Eagle Tuf Cut Tire Cutter: T-02290. The Eagle Tuf Cut adds flexibility to your tire processing operation by allowing you to accept and process tires up to 23.5/25 12 ply into your system. This diesel portable cutter is powered by a 23 hp Isuzu diesel, and it’s ready to go to work. It comes with a spare blade.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
50,000	US Dollar	each

Tire Industry Equipment - SSI 1500H Tire Shredder- T-02262. This SSI shredder is a hydraulic machine with 2 100 hp electric motors. It has an opening of 52 inches by 32 inches. The 2 inch knives will produce a primary shred out of car and passenger tires. This machine has just had a bearing replaced so it’s running real smooth. It is a clean machine that comes complete with the infeed and outfeed conveyors, stand, hopper, hydraulic power pak, and electric motor and controls. This shredder is ready to go to work and can be demonstrated on request.

Quantity	Units	Frequency
2	each	once
Price	Funds	Per Unit
95,000	US Dollars	each

Tire Industry Equipment - 48” Entoleter/ AlSteel Granulator: T0198 & or T0199. These machines have been completely refurbished and are presently better than new because we have beefed up many of the areas where we had noticed that wear was occurring. These areas were all welded back up to standard and then these areas have all been hard-faced with Stoody build up wire to slow down the wear in these areas in the future. The rotors on these machines were also hard-faced to cut down on the wear areas and we have also installed larger diameter bolt holes that hold all the fly knives in place. We had each knife holder on the rotors planed and squared up to make sure that all the fly knifes were held in place properly. We also had both of the rotors sent off and professionally balanced to make sure they operate with as little vibration as possible. We put new bearings on the shafts when we installed the rotors back in the machine. Also both of the bed knife holders were sent in and completely refurbished by a professional machine shop where they drilled out and inserted each of the existing bolt holes with new fine thread bolt holes. Also each of these bed knife holders were welded up and planed off to make sure that all the bed knives were mounted properly. All brand new knives were installed back in these machines both bed & fly knives. When you purchase these machines you will get a complete set of re-sharpened used knives with the machines as well. In addition we have several other spare wear parts that will go with these machines. These machines also have hydraulic folding hoppers and screen holders for easy access for making knife changes and screen changes. They also have water cooled jackets around the cutting chambers to allow them to operate cooler. These machines are powered by 250 H.P. electric motors and we will furnish with them brand new soft starts. These machines would work ideally for the processing of 1”-3/4” rubber chips down to 3/8”- ¼” rubber particles. We would estimate that these machines would each process around 3500-4,000 lbs per hour of this size material. This is an excellent matched pair of machines that are both ready to go to work. We don’t think you’ll find any better used “high production” machines in the country.

Quantity	Units	Frequency
one	each	once
Price	Funds	Per Unit
50,000	US Dollars	each

Tire Industry Equipment - Tire Wire Baler: T01101. We just finished checking this machine over in our shop and made several improvements to enhance the operation of the unit. We test ran the machine and produced several bales and after getting it properly adjusted we were able to make a very consistent size and weight bale. Note: the bales we were producing were 10” X 10” X 13” in size and weighed 30 lbs. Of course this will vary with the amount of rubber you have in your wire as well as the size wire you are trying to bale. This machine works and performs the same job as the Wendt tire wire balers that sell for over $200,000. Of course it’s not as automated but in the end you can produce a bale that is very comparable to the ones produced by the Wendt baler. Although it may be a little more labor intensive to operate, this machine offers a tremendous savings over purchasing a new machine to make the same or very similar sized bale. This machine is powered by a 25 H.P. electric motor that drives the hydraulic pumps and everything is then operated hydraulically through electrical pressure valves and relays. This unit comes complete with all the electrical controls needed to operate.